 |
???????ł́A德赢AC米兰官方合作伙伴?ł̐ݒ????????܂??B德赢AC米兰官方合作伙伴 iWAN Numbered?j,INFONET?
|
INFONET-RX20 Remote Router B V01.03 1998.04.15
WAN topology ( 6) 1998/07/01 15:30:26 ( 0 00:08:26) Normal Mode
1. configuration display
2. configuration set (normal)
3. configuration set (expert)
4. operation
5. information
6. shift to super mode
7. exit from remote console or current mode
Select the number. : 6?@?@?@??Super Mode?Ɉړ????܂?
New password: ?@?@?@???K???p?X???[?h?????Ă???????
Retype New password:
New password is accepted.
INFONET-RX20 Remote Router B V01.03 1998.04.15
WAN topology ( 6) 1998/07/01 15:30:30 ( 0 00:08:30) Super Mode
1. configuration display
2. configuration set (normal)
3. configuration set (expert)
4. operation
5. information
6. shift to super mode
7. exit from remote console or current mode
Select the number. : 2
*** Selecting PORT way ***
1 HSD, HSD
* 2 HSD, ISDN
3 FR, ISDN
Select the number. [2]:
*** Set current time parameter(s) ***
1998/07/01 15:30:35
Do you change (y/n)? [n]:
*** Set Default host name configuration ***
<Default host name configuration parameter(s)
host name :
password :
Do you change (y/n)? [n]:
*** Selecting WAN topology ***
<"L:" is load split, "B:" is backup, "L+B:" is load split and backup
1 HSD
2 HSD ( B:德赢AC米兰官方合作伙伴1)
3 HSD (L+B:德赢AC米兰官方合作伙伴1)
4 HSD (L+B:德赢AC米兰官方合作伙伴1,2)
5 HSD ( B:德赢AC米兰官方合作伙伴1,2)
* 6 德赢AC米兰官方合作伙伴1
7 德赢AC米兰官方合作伙伴1 (L :德赢AC米兰官方合作伙伴2)
8 HSD, 德赢AC米兰官方合作伙伴1
9 HSD, 德赢AC米兰官方合作伙伴1 (L :德赢AC米兰官方合作伙伴2)
10 德赢AC米兰官方合作伙伴1, 德赢AC米兰官方合作伙伴2
11 HSD ( B:德赢AC米兰官方合作伙伴1),德赢AC米兰官方合作伙伴2
12 HSD (L+B:德赢AC米兰官方合作伙伴1),德赢AC米兰官方合作伙伴2
13 HSD, 德赢AC米兰官方合作伙伴1, 德赢AC米兰官方合作伙伴2
Select the number. [6]: 1?@?@?@????p??1??????g?p???܂?
*** Main: Set HSD configuration ***
<Main HSD parameter(s)
speed : 0Kbps
Do you change (y/n)? [n]: y
speed(1:64K 2:128K) [2]: 1 ?@????????x??64kbps
Main HSD parameter(s) are set to the following values.
<Main HSD parameter(s)
speed : 64Kbps
Set OK (y/n)? [y]:
*** Set basic configuration ***
<Basic configuration parameter(s)
IP routing : use
IP filtering : not use
IPX routing : not use
AppleTalk routing: not use
bridging : not use
SNMP : use
Do you change (y/n)? [n]:
*** Set IP router configuration ***
<IP router configuration parameter(s)
routing interface list
broadcast or
IP address subnetmask remote address interface type
-------+----------------+----------------+----------------+--------------
LAN 192.52.150.1 255.255.255.0 192.52.150.255 broadcast
HSD 0.0.0.0 0.0.0.0 0.0.0.0 point to point
OSPF protocol: not use
Do you change (y/n)? [n]: y
LAN IP address [192.52.150.1]: 192.168.1.1
?????[?^??LAN?A?h???X
subnetmask [255.255.255.0]:
broadcast [192.168.1.255]:
HSD interface type (1:broadcast 2:point to point) [2]: 1
IP address []: 192.168.100.1
?????[?^??WAN?A?h???X
subnetmask [255.255.255.0]:
broadcast [192.168.100.255]:
OSPF protocol (1:use 2:not use) [2]:
IP router parameter(s) are set to the following values.
<IP router configuration parameter(s)
routing interface list
broadcast or
IP address subnetmask remote address interface type
-------+----------------+----------------+----------------+--------------
LAN 192.168.1.1 255.255.255.0 192.168.1.255 broadcast
HSD 192.168.100.1 255.255.255.0 192.168.100.255 broadcast
OSPF protocol: not use
Set OK (y/n)? [y]:
*** Set RIP(IP) motion configuration ***
<RIP(IP) motion parameter(s)
mode : supplier
default metric: 16
Do you change (y/n)? [n]:
*** Set RIP(IP) interface configuration ***
<RIP(IP) interface parameter(s)
send recv metric pre- broad- interval ageout time
control control ference cast (sec) (sec)
------+-------+-------+------+-------+------+----------+------+----------
LAN RIP1 RIP1,2 0 0 - - - -
HSD RIP1 RIP1,2 0 0 on 30 on 180
<RIP2 password
LAN : (not configured)
HSD : (not configured)
Do you change (y/n)? [n]: y
LAN RIP send control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [1]:
recv control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [3]:
password []:
metric [0]:
preference [0]:
HSD RIP send control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [1]: 4
??RIP???g?p???܂???
recv control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [3]: 4
??RIP???g?p???܂???
metric [0]:
preference [0]:
broadcast (1:on 2:off) [1]:
broadcast interval (sec) [30]:
RIP entry ageout (1:on 2:off) [1]:
ageout time (sec) [180]:
RIP(IP) interface parameter(s) are set to the following values.
<RIP(IP) interface parameter(s)
send recv metric pre- broad- interval ageout time
control control ference cast (sec) (sec)
------+-------+-------+------+-------+------+----------+------+----------
LAN RIP1 RIP1,2 0 0 - - - -
HSD off off 0 0 on 30 on 180
<RIP2 password
LAN : (not configured)
HSD :
Set OK (y/n)? [y]:
**** Set IP static routing configuration ***
1. change 2. delete 3. add 4. display 5. end
Select the number. [5]: 4
<IP static routing table (max 32 entries)
no dst address mask metric preference
gateway
---+---------------+---------------+------+----------
1. 0.0.0.0 ---.---.---.--- 16 50
德赢AC米兰官方合作伙伴1
*** Set IP static routing configuration ***
1. change 2. delete 3. add 4. display 5. end
Select the number. [5]: 2?@???K?v?łȂ??X?^?e?B?b?N???[?g???폜????
<Delete IP static routing data
Select the entry number. : 1
Selected IP static routing data:
no dst address mask metric preference
gateway
---+---------------+---------------+------+----------
1. 0.0.0.0 ---.---.---.--- 16 50
德赢AC米兰官方合作伙伴1
Delete OK (y/n)? [n]: y
*** Set IP static routing configuration ***
1. change 2. delete 3. add 4. display 5. end
Select the number. [5]: 3?@???X?^?e?B?b?N???[?g??ݒ肷??
<Add IP static routing data
destination address [0.0.0.0]: 192.168.2.0
mask [255.255.255.0]:
gateway type(1:IP address 2:Interface) [1]: 2
interface(1:HSD) []: 1
metric [16]:
preference [50]:
IP static routing data:
no dst address mask metric preference
gateway
---+---------------+---------------+------+----------
1. 192.168.2.0 255.255.255.0 16 50
HSD
Add OK (y/n)? [y]:
*** Set IP static routing configuration ***
1. change 2. delete 3. add 4. display 5. end
Select the number. [5]:
?F
?F?ȗ?
?F
Now you have set all configurations!
Do you display the configurations (y/n)? [y]: n
(Warning): Some configurations are not updated unless you reset
1. Save new parameter(s) and reset 3. Configurations set again
2. Save new parameter(s) only 4. Quit (no save and no reset)
Select the number. : 1?@?????Z?b?g???s??ꗧ???オ???A?ݒ肪?L???ł?
